Practice Free HPE6-A86 Exam Online Questions
A Solutions Architect is presenting a network design that includes both campus access layer switches (like the CX 6300) and data center switches (like the CX 8325). The customer is concerned about the complexity of managing different operating systems.
What is a key software differentiator of the HPE Aruba Networking switching portfolio that addresses this concern?
- A . Each switch series runs a completely different operating system optimized for its specific role.
- B . All CX switches run the same network operating system, AOS-CX, providing a consistent experience.
- C . The data center switches run AOS-CX, while the campus switches run the legacy ArubaOS-Switch software.
- D . The switches can be ordered with a choice of either AOS-CX or a third-party open network operating system.
Which of the statements describes valid VSF requirements and specifications? (Select three)
- A . You can daisy-chain up to 10 VSF members.
- B . You can connect 10 VSF members in a ring topology.
- C . You can mesh multiple members together for redundancy.
- D . If you use a CX 6300 Series as the conductor, you can connect 3810 Series switches as members.
- E . The configuration of VSF may cause members to reboot.
A Security Analyst is using a network sniffer to analyze a traffic capture. They are looking at a frame that was just received by a switch from a host.
[Ethernet II Header]
Destination MAC: 00:1b:77:54:7d:f0
Source MAC: 00:1b:77:54:7d:f1
EtherType: IPv4 (0x0800)
[IP Header]
Source IP: 192.168.1.10
Destination IP: 192.168.1.20
[TCP Header]
Source Port: 49152
Destination Port: 443
Which OSI model layer is primarily responsible for the information contained within the Ethernet II header?
- A . Layer 1 (Physical)
- B . Layer 2 (Data Link)
- C . Layer 3 (Network)
- D . Layer 4 (Transport)
A Security Analyst is explaining to a colleague why a standard switch cannot, by itself, stop the spread of a virus between two computers that are in the same VLAN.
Which statements accurately describe the function of a standard Layer 2 switch within the OSI model? (Select all that apply.)
- A . It operates primarily at the Network Layer (Layer 3).
- B . It forwards traffic based on the destination MAC address in the frame.
- C . It creates a single, large broadcast domain for all connected ports.
- D . It breaks up broadcast domains but not collision domains.
- E . It is unaware of the IP addresses or TCP ports being used in the traffic it forwards.
- F . It operates primarily at the Data Link Layer (Layer 2).
A Network Technician is connecting two switches in different buildings that are 1.5 kilometers apart. The required connection speed is 1Gbps.
Which combination of Layer 1 media and transceiver type is most appropriate for this connection?
- A . Multi-mode fiber and a 1000BASE-SX transceiver.
- B . Cat6a copper cable and an RJ-45 connector.
- C . Single-mode fiber and a 1000BASE-LX transceiver.
- D . Coaxial cable and a BNC connector.
Which aspect of Layer 3 analysis involves evaluating the operation and effectiveness of protocols such as RIP, OSPF, EIGRP, and BGP in dynamically exchanging routing information and building routing tables?
- A . Routing table analysis
- B . Routing convergence
- C . Route redistribution
- D . Routing protocols
A Network Operator needs to perform a basic, initial configuration on a new, out-of-the-box HPE Aruba Networking CX 6000 switch. The operator does not have a laptop with a serial port but is in the same room as the switch.
Besides the serial console, what is the default management method available on these switches for initial setup?
- A . The switch is unmanaged and requires a separate management module.
- B . The switch can only be managed via Aruba Central.
- C . The switch has a default IP address on VLAN 1, allowing for immediate web UI or SSH access.
- D . The switch has an out-of-band management (OOBM) port that can be used for direct connection.
A Network Operator is managing an HPE Aruba Networking CX 6300 switch. They need to securely manage the switch remotely using a graphical interface.
Which management option provides an encrypted, browser-based graphical user interface for switch configuration and monitoring?
- A . The serial console port
- B . The out-of-band management (OOBM) port
- C . The HTTPS web interface
- D . The Telnet service
A Solutions Architect is designing a highly available core layer for a campus network using two HPE Aruba Networking CX 8325 switches. The primary goals are to provide a single, unified management point, eliminate Spanning Tree Protocol (STP) for core links, and ensure seamless failover for downstream access layer switches and connected devices. The architect has chosen to implement Virtual Switching Framework (VSF) to stack the two core switches.
What is the primary benefit of using VSF in this design compared to traditional redundancy protocols like STP?
- A . It increases the number of available physical ports by combining the ports of both switches.
- B . It allows both switches in the stack to actively forward traffic simultaneously, effectively doubling the core bandwidth.
- C . It simplifies IP address management by assigning a separate IP address to each switch in the stack.
- D . It provides faster convergence than STP by using Layer 3 OSPF for loop prevention.
A Network Operator is managing a campus network with multiple HPE Aruba Networking CX switches. To ensure the ability to roll back to a known-good state before making significant changes, a checkpoint of the running configuration is created using the command `copy running-config checkpoint pre-change-01`. After making several configuration changes related to VLANs and routing, the operator discovers that the changes have caused network instability. They need to revert the switch to the exact state it was in before the changes were made.
Which command should the operator use to immediately restore the switch’s active configuration from the checkpoint?
- A . `copy startup-config running-config`
- B . `checkpoint rollback pre-change-01`
- C . `erase startup-config` followed by a reboot
- D . `copy checkpoint pre-change-01 startup-config` followed by a reboot