Practice Free D-PE-OE-23 Exam Online Questions
A technician must use the iDRAC UI to roll back a diagnostics firmware revision on a server that was updated four weeks previously. However, the replaced version cannot be found in the Firmware Rollback section on the iDRAC UI.
What is the cause of this issue?
- A . The Rollback feature was not enabled in iDRAC Settings.
- B . Diagnostics firmware is not supported in the Rollback feature.
- C . The Lifecycle Controller was not updated before the rollback.
- D . Firmware can only be rolled back within a week of being replaced.
A technician is replacing a fan on a mission critical PowerEdge R740 server that needs to stay operational. The server has no LCD.
How can the technician determine which fan needs to be replaced?
- A . Run embedded diagnostics to locate the failing fan
- B . Access the Lifecycle Controller, navigate to the System > Cooling section to locate the failing fan number
- C . Remove the chassis cover and observe a fan with an amber LED
- D . Use the iDRAC GUI to locate failing fan number
A technician builds a bootable ISO with Repository Manager, and then mounts the ISO via the iDRAC virtual console. After the updates have completed, the technician reboots the server to apply the updates. When reviewing the updates, the technician determines NOT all updates were applied.
What is causing this issue?
- A . The iDRAC update caused virtual media disconnect.
- B . A SUU repository must be used to update the firmware instead of the bootable ISO.
- C . An OS was NOT installed prior to upgrading the firmware.
- D . The firmware must be manually updated from the iDRAC.
A technician has a rack mount server with 20, 200 GB drives installed. The administrator needs three different RAID 5 virtual disks that are each 600 GB in size. All virtual disks must utilize the same set of physical disks.
How should the technician meet this requirement?
- A . Create a single disk group using 6 drives
Assign the virtual disks via the Lifecycle Controller - B . Create a virtual disk using 10 drives that are 600 GB in size
Split the remaining space into two virtual disks - C . Create three virtual disks that are each 600 GB in size
Assing these disks to the same disk group via Lifecycle Controller - D . Create three disk groups using 9 drives that are each 600 GB in size
Add virtual disks to each disk group
You have been tasked with configuring a Dell EMC PowerEdge server to be a file server. The server operating system has been installed and there are 8 x 1TB drives that must be configured.
Which RAID configuration would provide the maximum usable space with maximum redundancy?
- A . RAID 10
- B . RAID 5
- C . RAID 50
- D . RAID 0
Click UEFI boot sequence.
A technician is tasked to perform a RAID Level Migration (RLM) of a RAID 5 array to a RAID 6 array. The technician backs up data and looks in OpenManage Server Administrator to find that the current RAID 5 array is sliced into two virtual disks.
What should the technician do to achieve the desired RAID level?
- A . Delete the arrays and recreate new RAID 6 arrays
- B . Use iDRAC GUI under Storage > Virtual disks to complete RLM
- C . Use SupportAssist for Servers to complete RLM
- D . Delete the RAID 5 array and complete RLM using iDRAC GUI under Storage > Virtual disks
What are key characteristics of SupportAssist Enterprise on Dell EMC PowerEdge 14G servers?
- A . System generated
Proactive
Predictive - B . Automated
Proactive
Predictive - C . Manual intervention
Steady state
Remediation - D . Automated
Steady state
Predictive
A server has both processor sockets populated. An adapter card in the server is not functioning. However, no errors are displayed. The technician reboots the server, enters the System Setup utility, and selects System BIOS.
What should the technician do before replacing the adapter card?
- A . Select Integrated Device Settings > Slot Disablement
Verify that the adapter slot is enabled - B . Select System Profile > Custom
Verify that the adapter slots for both processors are enabled - C . Select Device Settings
Reset the adapter card to default settings - D . Select Processor Settings
Verify that the slots associated with processor 1 are enabled
A technician is configuring the server to boot to the Internal Dual SD Module.
Which BIOS boot option should the technician select?
- A . vFlash Media
- B . Hard Drive C
- C . DVD-ROM
- D . Integrated NIC