Practice Free 350-801 Exam Online Questions
An administrator is troubleshooting an issue where an 8845 is not joining the correct voice VLAN configuration from a switch and they believe that LLDP is the issue.
Which command allows the administrator to see the packets sent from the phone to the switch?
- A . show lldp status <interface>
- B . show lldp traffic
- C . show lldp
- D . show lldp run
An administrator configures international calling on a Cisco UCM cluster and wants to minimize the number of route patterns that are needed.
Which route pattern enables the administrator to match variable-length numbers?
- A . 9.011@
- B . 9.011#
- C . 9.011*
- D . 9.011!
A customer is deploying a SIP IOS gateway for a customer who requires that in-band DTMF relay is first priority and out-of-band DTMF relay is second priority.
Which IOS entry sets the required priority?
- A . dtmf-relay rtp-nte sip-notify
- B . dtmf-relay cisco-rtp
- C . sip-notify dtmf-relay rtp-nte
- D . dtmf-relay sip-kpml cisco-rtp
An administrator is integrating a Cisco Unity Express module to a Cisco UCME system. A test call is placed to the Cisco Unity Express pilot number, but the administrator receives a busy signal. The dial-peer is configured as follows: dial-peer voice 4100 voip destination-pattern 41.. session protocol sipv2 session target ipv4:10.1.10.1 dtmf-relay sip-notify no vad
How is this issue resolved?
- A . The dial-peer needs to be reconfigured to support the G.711 voice codec.
- B . The destination pattern needs to be changed to match the dialed number of 4100.
- C . The dial-peer needs to be reconfigured to support vad.
- D . The dial-peer needs to be reconfigured to support H.323 instead of SIP.
Which type of message must an administrator configure in the SIP Trunk Security Profile for a Message Waiting Indicator light to work with a SIP integration between Cisco UCM and Cisco Unity Connection?
- A . Unsolicited NOTIFY
- B . 200 ok
- C . SIP Register
A Cisco TelePresence SX80 suddenly has issues displaying main video to a display over HDMI.
Which command can you use from the SX80 admin CLI to check the video output status to the monitor?
- A . xStatus Video Output
- B . xCommand Video Status
- C . xConfiguration Video Output
- D . xStatus HDMI Output
Which wildcard must an engineer configure to match a whole domain in SIP route patterns?
- A . .
- B . !
- C . @
- D . *
What is NBAR?
- A . It controls the forwarding of routed packets
- B . It collects traffic flow statistics on routing devices
- C . It allows asymmetric flows that have stateful protocols
- D . It intelligently classifies traffic from different applications
An engineer troubleshoots a Cisco Jabber login problem on a Windows PC. The login fails with the error message `Cannot find your services automatically. Click advanced settings to set up manually.`
Which action should the engineer take first?
- A . Verify whether the cup-xmpp certificates are valid
- B . Perform a manual DNS lookup of SRV record_collab-edge._tls.domain.com
- C . Verify the username and password and try again
- D . Perform a manual DNS lookup of SRV record_cisco-uds._tcp.domain.com
An administrator works with an ISDN PRI that is connected to a third-party PBX. The ISDN link does not come up, and the administrator finds that the third-part PBX uses the QSIG signaling method.
Which command enables the Cisco IOS Gateway to use QSIG signaling on the ISDN link?
- A . isdn switch-type basic-qsig
- B . isdn switch-type basic-ni
- C . isdn switch-type primary-qsig
- D . isdn incoming-voice voice