Practice Free JN0-352 Exam Online Questions
Click the Exhibit button.
A network includes several autonomous systems that exchange routing information using BGP. Multiple BGP routes exist for the same prefix.
Referring to the exhibit, which attribute would BGP use first when selecting a preferred route?
- A . local preference
- B . origin type
- C . MED
- D . AS path length
Click the Exhibit button.
You have three Juniper Networks EX Series Switches in an STP domain as shown in the exhibit.
Which statement describes the switch that will be elected as the root bridge?
- A . EX-2, because its priority is the lowest.
- B . EX-2, because its MAC address is the lowest.
- C . EX-1, because its MAC address is highest.
- D . EX-1, because its priority is the highest.
Click the Exhibit button.
Which two statements about the output shown in the exhibit are correct? (Choose two.)
- A . R3 advertises its loopback interface IP address.
- B . R3 cannot establish an L2 adjacency on the ge-0/0/2.0 interface.
- C . R3 uses its loopback interface to establish an L2 IS-IS adjacency.
- D . A designated router is elected for each IS-IS interface.
You need to block SSH (TCP port 22) traffic from the 192.168.10.0/24 network.
Which firewall filter term is correct in this scenario?
- A . Option A
- B . Option B
- C . Option C
- D . Option D
What are three valid OSPF adjacency states? (Choose three.)
- A . reject
- B . loading
- C . down
- D . init
- E . established
Click the Exhibit button.
You need to apply a Layer 2 firewall filter on a Juniper Networks EX Series Switch to block traffic from the source MAC address 00:12:34:56:00:07 entering the switch on ge-0/0/3. After committing the configuration, traffic from the MAC address still passes through.
Referring to the exhibit, which statement is correct in this scenario?
- A . The filter is applied in the wrong direction.
- B . The MAC address and mask in the firewall filter need to be explicit.
- C . The interface needs to be of type trunk for the filter to evaluate correctly.
- D . Firewall filters under family ethernet-switching cannot match on MAC addresses.
Click the Exhibit button.
R1 is not responding to ICMP requests sent to the VIP address.
Referring to the exhibit, which command option would you configure on the virtual address to correct this problem?
- A . advertise-interval
- B . track
- C . accept-data
- D . no-preempt
Which IS-IS PDU should be used by a router to list all LSPs that it believes should exist in the link-state database?
- A . LSP
- B . IIH
- C . PSNP
- D . CSNP
Two Juniper Networks EX Series Switches are connected with four 1-GbE links configured as a single link aggregation group (LAG). One of the physical member links experiences a failure.
By default, what impact will this failure have on traffic forwarding between the switches?
- A . The LAG continues forwarding traffic across the remaining member links.
- B . Only broadcast traffic continues to be forwarded across the LAG.
- C . The LAG renegotiates and temporarily disables all member links.
- D . All traffic will be dropped because the LAG goes administratively down.
Click the Exhibit button.
Devices on VLAN 5 and VLAN 7 need to communicate with each other.
Referring to the exhibit, what will satisfy this requirement?
- A . Configure a family inet interface connecting the two VLANs and assign both subnet IPs to it using secondary addressing.
- B . Create an integrated routing and bridging (IRB) interface for each VLAN, assign the gateway IP to each IRB, and enable static routing.
- C . Add both VLANs to a single trunk port and enable the Multiple VLAN Registration Protocol.
- D . Enable spanning tree on both VLANs and set the EX Series Switch as the root bridge.